1.1
This document explains the requirements for end-point assessment (EPA) for the building services engineering installer apprenticeship. End-point assessment organisations (EPAOs) must follow this when designing and delivering the EPA.
Building services engineering installer apprentices, their employers and training providers should read this document.
A full-time building services engineering installer apprentice typically spends 24 months on-programme. The apprentice must spend at least 12 months on-programme and complete the required amount of off-the-job training in line with the apprenticeship funding rules.
The EPA should be completed within an EPA period lasting typically 3 months.
The apprentice must complete their training and meet the gateway requirements before starting their EPA. The EPA will assess occupational competence.
An approved EPAO must conduct the EPA for this apprenticeship. Employers must work with the training provider to select an approved EPAO from the apprenticeship providers and assessment register (APAR).
This EPA has 3 assessment methods.
The grades available for each assessment method are below.
Assessment method 1 - multiple-choice test:
Assessment method 2 - interview underpinned by a portfolio of evidence:
Assessment method 3 - practical task with questions:
The result from each assessment method is combined to decide the overall apprenticeship grade. The following grades are available for the apprenticeship:
The EPA is taken in the EPA period. The EPA period starts when the EPAO confirms the gateway requirements have been met and is typically 3 months.
The EPAO should confirm the gateway requirements have been met and start the EPA as quickly as possible.
The apprentice’s employer must be content that the apprentice is occupationally competent. That is, they are deemed to be working at or above the level set out in the apprenticeship standard and ready to undertake the EPA. The employer may take advice from the apprentice's training provider, but the employer must make the decision. The apprentice will then enter the gateway.
The apprentice must meet the gateway requirements before starting their EPA.
They must:
Portfolio of evidence requirements:
The apprentice must compile a portfolio of evidence during the on-programme period of the apprenticeship. It should only contain evidence related to the KSBs that will be assessed by the interview. It will typically contain 10 discrete pieces of evidence. Evidence must be mapped against the KSBs. Evidence may be used to demonstrate more than one KSB; a qualitative as opposed to quantitative approach is suggested.
Evidence sources may include:
This is not a definitive list; other evidence sources can be included.
The portfolio of evidence should not include reflective accounts or any methods of self-assessment. Any employer contributions should focus on direct observation of performance, for example, witness statements, rather than opinions. The evidence provided should be valid and attributable to the apprentice; the portfolio of evidence should contain a statement from the employer and apprentice confirming this.
The EPAO should not assess the portfolio of evidence directly as it underpins the interview. The independent assessor should review the portfolio of evidence to prepare questions for the interview. They are not required to provide feedback after this review.
Gateway evidence must be submitted to the EPAO, along with any organisation specific policies and procedures requested by the EPAO.
The assessment methods can be delivered in any order.
The result of one assessment method does not need to be known before starting the next.
In the multiple-choice test, the apprentice answers questions in a controlled and invigilated environment. It gives the apprentice the opportunity to demonstrate the knowledge mapped to this assessment method.
This assessment method is being used because:
The multiple-choice test must be structured to give the apprentice the opportunity to demonstrate the knowledge mapped to this assessment method to the highest available grade.
The test can be computer or paper based.
The test will consist of 40 multiple-choice questions.
Multiple-choice questions must have four options, including one correct answer.
The apprentice must be given at least 2 weeks’ notice of the date and time of the test.
The apprentice must have 60 minutes to complete the test.
The test is closed book which means that the apprentice cannot refer to reference books or materials whilst taking the test.
The test must be taken in the presence of an invigilator who is the responsibility of the EPAO. The EPAO must have an invigilation policy setting out how the test must be conducted. It must state the ratio of apprentices to invigilators for the setting and allow the test to take place in a secure way.
The EPAO must verify the apprentice’s identity and ensure invigilation of the apprentice for example, with 360-degree cameras and screen sharing facilities.
The EPAO is responsible for the security of the test including the arrangements for on-line testing. The EPAO must ensure that their security arrangements maintain the validity and reliability of the test.
The test must be marked by an independent assessor or marker employed by the EPAO. They must follow a marking scheme produced by the EPAO. Marking by computer is allowed where question types support this.
A correct answer gets 1 mark.
Any incorrect or missing answers get zero marks.
The EPAO is responsible for overseeing the marking of the test.
The apprentice must take the test in a suitably controlled and invigilated environment that is a quiet room, free from distractions and influence. The EPAO must check the venue is suitable.
The test can take place remotely if the appropriate technology and systems are in place to prevent malpractice.
The EPAO must develop a purpose-built assessment specification and question bank. It is recommended this is done in consultation with employers of this occupation. The EPAO should maintain the security and confidentiality of EPA materials when consulting with employers. The assessment specification and question bank must be reviewed at least once a year to ensure they remain fit-for-purpose.
The assessment specification must be relevant to the occupation and demonstrate how to assess the KSBs mapped to this assessment method. The EPAO must ensure that questions are refined and developed to a high standard. The questions must be unpredictable. A question bank of sufficient size will support this.
The EPAO must ensure that the apprentice has a different set of questions in the case of re-sits or re-takes.
The EPAO must produce the following materials to support the test:
The EPAO must ensure that the EPA materials are subject to quality assurance procedures including standardisation and moderation.
In the interview, an independent assessor asks the apprentice questions. It gives the apprentice the opportunity to demonstrate the KSBs mapped to this assessment method.
The apprentice can refer to and illustrate their answers with evidence from their portfolio of evidence.
This assessment method is being used because:
The interview must be structured to give the apprentice the opportunity to demonstrate the KSBs mapped to this assessment method to the highest available grade.
An independent assessor must conduct and assess the interview.
The purpose is to assess the apprentice's competence against the following themes:
The EPAO must give an apprentice 2 weeks' notice of the interview.
The independent assessor must have at least 2 weeks to review the supporting documentation.
The apprentice must have access to their portfolio of evidence during the interview.
The apprentice can refer to and illustrate their answers with evidence from their portfolio of evidence however, the portfolio of evidence is not directly assessed.
The interview must last for 60 minutes. The independent assessor can increase the time of the interview by up to 10%. This time is to allow the apprentice to respond to a question if necessary.
The apprentice may choose to end any assessment method early. The apprentice must be confident they have demonstrated competence against the assessment requirements for the assessment method. The independent assessor or EPAO must ensure the apprentice is fully aware of all assessment requirements. The independent assessor or EPAO cannot suggest or choose to end any assessment methods early (unless in an emergency). The EPAO is responsible for ensuring the apprentice understands the implications of ending an assessment early if they choose to do so. The independent assessor may suggest the assessment continues. The independent assessor must document the apprentice’s request to end any assessment early.
The independent assessor must ask at least 6 questions. The independent assessor must use the questions from the EPAO’s question bank or create their own questions in line with the EPAO’s training. Follow-up questions are allowed where clarification is required.
The independent assessor must make the grading decision.
The independent assessor must keep accurate records of the assessment. They must record:
The interview must take place in a suitable venue selected by the EPAO for example, the EPAO’s or employer’s premises.
The interview can be conducted by video conferencing. The EPAO must have processes in place to verify the identity of the apprentice and ensure the apprentice is not being aided.
The interview should take place in a quiet room, free from distractions and influence.
The EPAO must develop a purpose-built assessment specification and question bank. It is recommended this is done in consultation with employers of this occupation. The EPAO must maintain the security and confidentiality of EPA materials when consulting with employers. The assessment specification and question bank must be reviewed at least once a year to ensure they remain fit-for-purpose.
The assessment specification must be relevant to the occupation and demonstrate how to assess the KSBs mapped to this assessment method. The EPAO must ensure that questions are refined and developed to a high standard. The questions must be unpredictable. A question bank of sufficient size will support this.
The EPAO must ensure that the apprentice has a different set of questions in the case of re-sits or re-takes.
The EPAO must produce the following materials to support the interview underpinned by a portfolio of evidence:
The EPAO must ensure that the EPA materials are subject to quality assurance procedures including standardisation and moderation.
In a practical task with questions, an independent assessor observes the apprentice completing a task or series of tasks set by the EPAO. The EPAO decides in which of the simulated environments it takes place. The assessment environment must closely relate to the apprentice’s natural working environment. It gives the apprentice the opportunity to demonstrate the KSBs mapped to this assessment method.
This assessment method is being used because:
The practical task with questions must be structured to give the apprentice the opportunity to demonstrate the KSBs mapped to this assessment method to the highest available grade.
An independent assessor must conduct and assess the practical task with questions.
The independent assessor must only observe one apprentice at a time to ensure quality and rigour. They must be as unobtrusive as possible.
The EPAO must give an apprentice 2 weeks' notice of the . practical task with questions
The practical task with questions must take 6 hours.
The independent assessor can increase the time of the practical task with questions by up to 10%. This time is to allow the apprentice to complete a task or respond to a question if necessary.
The apprentice may choose to end any assessment method early. The apprentice must be confident they have demonstrated competence against the assessment requirements for the assessment method. The independent assessor or EPAO must ensure the apprentice is fully aware of all assessment requirements. The independent assessor or EPAO cannot suggest or choose to end any assessment methods early (unless in an emergency). The EPAO is responsible for ensuring the apprentice understands the implications of ending an assessment early if they choose to do so. The independent assessor may suggest the assessment continues. The independent assessor must document the apprentice’s request to end any assessment early.
The practical task with questions cannot be split, other than for comfort breaks or to allow apprentices to move from one location to another. Where breaks occur, they will not count towards the total EPA time.
The EPAO must manage invigilation of the apprentice during the assessment, to maintain security of the EPA, in line with their malpractice policy. This includes breaks and moving between locations.
The independent assessor must explain to the apprentice the format and timescales of the practical task with questions before it starts. This does not count towards the assessment time.
The independent assessor must observe the following during the practical task:
These activities provide the apprentice with the opportunity to demonstrate the KSBs mapped to this assessment method.
Task 1 - planning, preparation and set out task
This task requires the apprentice to interpret and follow a written brief detailing the planning and setting out of materials, components and bracketry from which a pipework system will be fabricated in preparation for installation.
The work area must contain, as a minimum:
The apprentice will be observed carrying out preparation activities including:
Task 2 - fabrication task
This task requires the apprentice to combine components, bracketry and materials to fabricate the pipework system to be installed.
The work area must contain, as a minimum:
The apprentice will be observed carrying out fabrication activities including:
Task 3 - installation task
This task requires the apprentice to install their fabricated pipework system in a designated work area.
The work area must contain, as a minimum:
The apprentice will be observed carrying out installation activities including:
Task 4 - testing task
This task requires the apprentice to test the fabricated and installed pipework, components and fittings.
The work area must contain, as a minimum:
The apprentice will be observed carrying out testing activities including:
Task 5 - decommissioning and disassembling task
This task requires the apprentice to carry out decommissioning practices to remove the installation from the work area and disassemble the installed pipework, bracketry and components.
The work area must contain, as a minimum:
The apprentice will be observed carrying out decommissioning and disassembling activities including:
The independent assessor must ask questions.
The purpose of the questions is:
The independent assessor must keep accurate records of the assessment. They must record:
The practical task with questions must take place in a simulated environment selected by the EPAO for example, the EPAO’s premises, a training provider’s premises, a training facility in the employer’s premises, a test centre or a similar simulated environment. This simulated environment must relate to the apprentice’s natural work environment. Equipment and resources needed for the practical task with questions must be provided by the EPAO, who can liaise with the employer to provide these.
The EPAO must develop a purpose-built assessment specification and question bank. It is recommended this is done in consultation with employers of this occupation. The EPAO must maintain the security and confidentiality of EPA materials when consulting with employers. The assessment specification and question bank must be reviewed at least once a year to ensure they remain fit-for-purpose.
The assessment specification must be relevant to the occupation and demonstrate how to assess the KSBs mapped to this assessment method. The EPAO must ensure that questions are refined and developed to a high standard. The questions must be unpredictable. A question bank of sufficient size will support this.
The EPAO must ensure that the apprentice has a different set of tasks and questions in the case of re-sits and retakes, to minimise predictability.
The EPAO must produce the following materials to support the practical task with questions:
The EPAO must ensure that the EPA materials are subject to quality assurance procedures including standardisation and moderation.
Performance in the EPA determines the overall grade of:
An independent assessor must individually grade the interview underpinned by a portfolio of evidence and practical task with questions in line with this EPA plan.
The EPAO must combine the individual assessment method grades to determine the overall EPA grade.
If the apprentice fails one assessment method or more, they will be awarded an overall fail.
To achieve an overall pass, the apprentice must achieve at least a pass in all the assessment methods. To achieve an overall distinction the apprentice must achieve a distinction within the multiple-choice test, a distinction within the interview and a pass within the practical.
Grades from individual assessment methods must be combined in the following way to determine the grade of the EPA overall.
If the apprentice fails one assessment method or more, they can take a re-sit or a re-take at their employer’s discretion. The apprentice’s employer needs to agree that a re-sit or re-take is appropriate. A re-sit does not need further learning, whereas a re-take does. The apprentice should have a supportive action plan to prepare for a re-sit or a re-take.
The employer and the EPAO should agree the timescale for a re-sit or re-take. A re-sit is typically taken within 2 months of the EPA outcome notification. The timescale for a re-take is dependent on how much re-training is required and is typically taken within 3 months of the EPA outcome notification.
Failed assessment methods must be re-sat or re-taken within a 6-month period from the EPA outcome notification, otherwise the entire EPA will need to be re-sat or re-taken in full.
Re-sits and re-takes are not offered to an apprentice wishing to move from pass to a higher grade.
The apprentice will get a maximum EPA grade of pass for a re-sit or re-take, unless the EPAO determines there are exceptional circumstances.
The EPAO must have reasonable adjustments arrangements for the EPA.
This should include:
Adjustments must maintain the validity, reliability and integrity of the EPA as outlined in this EPA plan.
Internal quality assurance refers to the strategies, policies and procedures that an EPAO must have in place to ensure valid, consistent and reliable EPA decisions.
EPAOs for this EPA must adhere to the requirements within the roles and responsibilities table.
They must also appoint independent assessors who:
Affordability of the EPA will be aided by using at least some of the following:
This apprenticeship is not aligned to professional recognition.
| Version | Change detail | Earliest start date | Latest start date |
|---|---|---|---|
| 1.1 | Occupational standard, end-point assessment and funding band revised. | 01/08/2024 | Not set |
| 1.0 | Approved for delivery | 24/03/2016 | 31/07/2024 |
Crown copyright © 2025. You may re-use this information (not including logos) free of charge in any format or medium, under the terms of the Open Government Licence. Visit www.nationalarchives.gov.uk/doc/open-government-licence