V1.4
This document explains the requirements for end-point assessment (EPA) for the wall and floor tiler apprenticeship. End-point assessment organisations (EPAOs) must follow this when designing and delivering the EPA.
Wall and floor tiler apprentices, their employers and training providers should read this document.
A full-time wall and floor tiler apprentice typically spends 30 months on-programme. The apprentice must spend at least 12 months on-programme and complete the required amount of off-the-job training in line with the apprenticeship funding rules.
The EPA should be completed within an EPA period lasting typically 3 months.
The apprentice must complete their training and meet the gateway requirements before starting their EPA. The EPA will assess occupational competence.
An approved EPAO must conduct the EPA for this apprenticeship. Employers must work with the training provider to select an approved EPAO from the apprenticeship providers and assessment register (APAR).
This EPA has 3 assessment methods.
The grades available for each assessment method are below.
Assessment method 1 - knowledge test:
Assessment method 2 - practical assessment with questions:
Assessment method 3 - interview underpinned by a portfolio of evidence:
The result from each assessment method is combined to decide the overall apprenticeship grade. The following grades are available for the apprenticeship:
The EPA is taken in the EPA period. The EPA period starts when the EPAO confirms the gateway requirements have been met and is typically 3 months.
The EPAO should confirm the gateway requirements have been met and start the EPA as quickly as possible.
The apprentice’s employer must be content that the apprentice is occupationally competent. That is, they are deemed to be working at or above the level set out in the apprenticeship standard and ready to undertake the EPA. The employer may take advice from the apprentice's training provider, but the employer must make the decision. The apprentice will then enter the gateway.
The apprentice must meet the gateway requirements before starting their EPA.
They must:
Portfolio of evidence requirements:
The apprentice must compile a portfolio of evidence during the on-programme period of the apprenticeship. It should only contain evidence related to the KSBs that will be assessed by the interview. It will typically contain 15 discrete pieces of evidence. Evidence must be mapped against the KSBs. Evidence may be used to demonstrate more than one KSB; a qualitative as opposed to quantitative approach is suggested.
Evidence sources may include:
This is not a definitive list; other evidence sources can be included.
The portfolio of evidence should not include reflective accounts or any methods of self-assessment. Any employer contributions should focus on direct observation of performance, for example, witness statements, rather than opinions. The evidence provided should be valid and attributable to the apprentice; the portfolio of evidence should contain a statement from the employer and apprentice confirming this.
The EPAO should not assess the portfolio of evidence directly as it underpins the interview. The independent assessor should review the portfolio of evidence to prepare questions for the interview. They are not required to provide feedback after this review.
Simulated environments
Capturing evidence in simulated environments is about helping ensure that there is fair opportunity for apprentices to gather evidence for the interview underpinned by a portfolio of evidence in exceptional circumstances. Simulated environments may only be used where apprentices are prevented from capturing evidence in the workplace.
Typical causes are:
In the first instance the employer should make every effort to access an alternative workplace environment for their apprentice. Simulated environments must:
KSBs in scope of simulation for this apprenticeship and assessment method are:
S4 Use access and work at height equipment, for example step ladders, podium steps, hop up safety platforms.
S14 Install electric under-tile heating.
Gateway evidence must be submitted to the EPAO, along with any organisation specific policies and procedures requested by the EPAO.
The assessment methods can be delivered in any order.
The result of one assessment method does not need to be known before starting the next.
In the knowledge test, the apprentice answers questions in a controlled and invigilated environment. It gives the apprentice the opportunity to demonstrate the knowledge mapped to this assessment method.
This assessment method is being used because: .
The knowledge test must be structured to give the apprentice the opportunity to demonstrate the knowledge mapped to this assessment method to the highest available grade.
The test must be computer based.
The test will consist of 40 multiple-choice questions.
Multiple-choice questions must have four options, including one correct answer.
The apprentice must be given at least 2 weeks’ notice of the date and time of the test.
The apprentice must have 70 minutes to complete the test.
The test is closed book which means that the apprentice cannot refer to reference books or materials whilst taking the test.
The test must be taken in the presence of an invigilator who is the responsibility of the EPAO. The EPAO must have an invigilation policy setting out how the test must be conducted. It must state the ratio of apprentices to invigilators for the setting and allow the test to take place in a secure way.
The EPAO must verify the apprentice’s identity and ensure invigilation of the apprentice for example, with 360-degree cameras and screen sharing facilities.
The EPAO is responsible for the security of the test including the arrangements for on-line testing. The EPAO must ensure that their security arrangements maintain the validity and reliability of the test.
The test must be marked by an independent assessor or marker employed by the EPAO. They must follow a marking scheme produced by the EPAO. Marking by computer is allowed where question types support this.
A correct answer gets 1 mark.
Any incorrect or missing answers get zero marks.
The EPAO is responsible for overseeing the marking of the test.
The apprentice must take the test in a suitably controlled and invigilated environment that is a quiet room, free from distractions and influence. The EPAO must check the venue is suitable.
The test can take place remotely if the appropriate technology and systems are in place to prevent malpractice.
The EPAO must develop a purpose-built assessment specification and question bank. It is recommended this is done in consultation with employers of this occupation. The EPAO should maintain the security and confidentiality of EPA materials when consulting with employers. The assessment specification and question bank must be reviewed at least once a year to ensure they remain fit-for-purpose.
The assessment specification must be relevant to the occupation and demonstrate how to assess the KSBs mapped to this assessment method. The EPAO must ensure that questions are refined and developed to a high standard. The questions must be unpredictable. A question bank of sufficient size will support this.
The EPAO must ensure that the apprentice has a different set of questions in the case of re-sits or re-takes.
The EPAO must produce the following materials to support the test:
The EPAO must ensure that the EPA materials are subject to quality assurance procedures including standardisation and moderation.
In a practical assessment with questions, an independent assessor observes the apprentice completing a task or series of tasks set by the EPAO. The EPAO decides in which of the simulated environments it takes place. The assessment environment must closely relate to the apprentice’s natural working environment. It gives the apprentice the opportunity to demonstrate the KSBs mapped to this assessment method.
This assessment method is being used because:
The practical assessment with questions must be structured to give the apprentice the opportunity to demonstrate the KSBs mapped to this assessment method to the highest available grade.
An independent assessor must conduct and assess the practical assessment with questions.
The independent assessor must only observe 4 apprentices at a time to ensure quality and rigour. They must be as unobtrusive as possible.
The EPAO must give an apprentice 2 weeks' notice of the . practical assessment with questions
The practical assessment with questions must take 12 hours.
The independent assessor can increase the time of the practical assessment with questions by up to 10%. This time is to allow the apprentice to complete a task or respond to a question if necessary.
The practical assessment with questions may take place in parts but must be completed over 2 consecutive working days. A working day is typically considered to be 7.5 hours long. The reason for this split is due to the drying time for tile adhesive and therefore potentially being unable to complete grouting until the next day.
The EPAO must manage invigilation of the apprentice during the assessment, to maintain security of the EPA, in line with their malpractice policy. This includes breaks and moving between locations.
The independent assessor must explain to the apprentice the format and timescales of the practical assessment with questions before it starts. This does not count towards the assessment time.
The independent assessor must observe the following during the practical assessment:
The apprentice must complete the following two tasks:
Task 1: Tile a minimum wall area of 2.5m squared (m2) in a brick or stacker bond pattern with tiles sized up to 300mm x 300mm.
Task 2: Tile a minimum floor area of 3m squared (m2) in a brick or stacker bond pattern with tiles sized up to 600mm x 600mm.
| Specific tolerances | |||
| Fail | Pass | Distinction | |
| Wall tiles plumb | More than + or – 3mm | + or – 3mm | + or – 1mm |
| Floor tiles level | More than + or – 3mm | + or – 3mm | + or – 1mm |
| Joint widths to specification | More than + or – 2mm | + or – 2mm | + or – 1mm |
| Wall joints plumb | More than + or – 3mm | + or – 3mm | + or – 1mm |
| Floor joints in line | More than + or – 3mm | + or – 3mm | + or – 1mm |
| No loose wall or floor tiles | |||
| Floor tiles visual discrepancies | Over 3 | 2 – 3 | 0 - 1 |
| Note: a visual discrepancy should be measured as a defect greater than 15 mm in diameter or length, such as adhesive marks, tile chips or grout marks | |||
| Wall tiles visual discrepancies | Over 3 | 2 – 3 | 0 - 1 |
| Note: a visual discrepancy should be measured as a defect greater than 15 mm in diameter or length, such as adhesive marks, tile chips or grout marks |
The two tasks collectively must set a requirement that is comparable to the work achieved by a competent wall and floor tiler in 12 hours.
An additional person, trained in manual handling, may be used during the practical assessment by the apprentice where 2 people are required in line with the role and responsibilities table.
|
These activities provide the apprentice with the opportunity to demonstrate the KSBs mapped to this assessment method.
The independent assessor must ask questions.
The purpose of the questions is:
Questioning must occur during the practical assessment. The time for questioning is included in the overall assessment time.
The independent assessor must ask at least 3 questions during the practical assessment. To remain as unobtrusive as possible, the independent assessor should ask questions during natural breaks in work rather than disrupting the apprentice’s flow. The independent assessor must use the questions from their EPAO’s question bank or create their own questions in line with the EPAO’s training.
The independent assessor can ask follow-up questions to clarify answers given by the apprentice. These questions are in addition to the above set number of questions for the practical assessment with questions.
The independent assessor must make the grading decision. The independent assessor must assess the practical assessment and responses to questions holistically when deciding the grade.
The independent assessor must keep accurate records of the assessment. They must record:
The practical assessment with questions must take place in a simulated environment selected by the EPAO for example, the EPAO’s premises, a training provider’s premises, a training facility in the employer’s premises, a test centre or a similar simulated environment. This simulated environment must relate to the apprentice’s natural work environment. Equipment and resources needed for the practical assessment with questions must be provided by the EPAO, who can liaise with the employer to provide these.
The EPAO must develop a purpose-built assessment specification and question bank. It is recommended this is done in consultation with employers of this occupation. The EPAO must maintain the security and confidentiality of EPA materials when consulting with employers. The assessment specification and question bank must be reviewed at least once a year to ensure they remain fit-for-purpose.
The assessment specification must be relevant to the occupation and demonstrate how to assess the KSBs mapped to this assessment method. The EPAO must ensure that questions are refined and developed to a high standard. The questions must be unpredictable. A question bank of sufficient size will support this.
The EPAO must ensure that the apprentice has a different set of tasks and questions in the case of re-sits and retakes, to minimise predictability.
The EPAO must produce the following materials to support the practical assessment with questions:
The EPAO must ensure that the EPA materials are subject to quality assurance procedures including standardisation and moderation.
In the interview, an independent assessor asks the apprentice questions. It gives the apprentice the opportunity to demonstrate the KSBs mapped to this assessment method.
The apprentice can refer to and illustrate their answers with evidence from their portfolio of evidence.
This assessment method is being used because:
The interview must be structured to give the apprentice the opportunity to demonstrate the KSBs mapped to this assessment method to the highest available grade.
An independent assessor must conduct and assess the interview.
The EPAO must give an apprentice 2 weeks' notice of the interview.
The independent assessor must have at least 2 weeks to review the supporting documentation.
The apprentice must have access to their portfolio of evidence during the interview.
The apprentice can refer to and illustrate their answers with evidence from their portfolio of evidence however, the portfolio of evidence is not directly assessed.
The interview must last for 45 minutes. The independent assessor can increase the time of the interview by up to 10%. This time is to allow the apprentice to respond to a question if necessary.
The independent assessor must ask at least 6 questions. The independent assessor must use the questions from the EPAO’s question bank. Follow-up questions are allowed where clarification is required.
The independent assessor must make the grading decision.
The independent assessor must keep accurate records of the assessment. They must record:
The interview must take place in a suitable venue selected by the EPAO for example, the EPAO’s, training provider's or employer’s premises.
The interview can be conducted by video conferencing. The EPAO must have processes in place to verify the identity of the apprentice and ensure the apprentice is not being aided.
The interview should take place in a quiet room, free from distractions and influence.
The EPAO must develop a purpose-built assessment specification and question bank. It is recommended this is done in consultation with employers of this occupation. The EPAO must maintain the security and confidentiality of EPA materials when consulting with employers. The assessment specification and question bank must be reviewed at least once a year to ensure they remain fit-for-purpose.
The assessment specification must be relevant to the occupation and demonstrate how to assess the KSBs mapped to this assessment method. The EPAO must ensure that questions are refined and developed to a high standard. The questions must be unpredictable. A question bank of sufficient size will support this.
The EPAO must ensure that the apprentice has a different set of questions in the case of re-sits or re-takes.
The EPAO must produce the following materials to support the interview underpinned by a portfolio of evidence:
The EPAO must ensure that the EPA materials are subject to quality assurance procedures including standardisation and moderation.
Performance in the EPA determines the overall grade of:
An independent assessor must individually grade the practical assessment with questions and interview underpinned by a portfolio of evidence in line with this EPA plan.
The EPAO must combine the individual assessment method grades to determine the overall EPA grade.
If the apprentice fails one assessment method or more, they will be awarded an overall fail.
To achieve an overall pass, the apprentice must achieve at least a pass in all the assessment methods. To achieve an overall merit the apprentice must achieve a pass in the knowledge test and interview underpinned by a portfolio and a distinction in the practical assessment with questions. To achieve an overall distinction the apprentice must achieve a pass in the knowledge test and a distinction in the interview underpinned by a portfolio and the practical with questions.
Grades from individual assessment methods must be combined in the following way to determine the grade of the EPA overall.
If the apprentice fails one assessment method or more, they can take a re-sit or a re-take at their employer’s discretion. The apprentice’s employer needs to agree that a re-sit or re-take is appropriate. A re-sit does not need further learning, whereas a re-take does. The apprentice should have a supportive action plan to prepare for a re-sit or a re-take.
The employer and the EPAO should agree the timescale for a re-sit or re-take. A re-sit is typically taken within 2 months of the EPA outcome notification. The timescale for a re-take is dependent on how much re-training is required and is typically taken within 4 months of the EPA outcome notification.
Failed assessment methods must be re-sat or re-taken within a 6-month period from the EPA outcome notification, otherwise the entire EPA will need to be re-sat or re-taken in full.
Re-sits and re-takes are not offered to an apprentice wishing to move from pass to a higher grade.
The apprentice will get a maximum EPA grade of if pass they need to re-sit or re-take one or more assessment methods, unless the EPAO determines there are exceptional circumstances.
The EPAO must have reasonable adjustments arrangements for the EPA.
This should include:
Adjustments must maintain the validity, reliability and integrity of the EPA as outlined in this EPA plan.
Special considerations
The EPAO must have special consideration arrangements for the EPA.
This should include:
Special considerations must maintain the validity, reliability and integrity of the EPA as outlined in this EPA plan.
Internal quality assurance refers to the strategies, policies and procedures that an EPAO must have in place to ensure valid, consistent and reliable EPA decisions.
EPAOs for this EPA must adhere to the requirements within the roles and responsibilities table.
They must also appoint independent assessors who:
Affordability of the EPA will be aided by using at least some of the following:
This apprenticeship is not aligned to professional recognition.
| Version | Change detail | Earliest start date | Latest start date |
|---|---|---|---|
| 1.4 | Occupational standard and end-point assessment plan revised to reduce the wall tile size in the practical assessment. Add the requirement for tile pattern to be brick or stacker bond in the practical assessment. Amend practical assessment and S18 to grout wall or floor tiles rather than both. | 16/12/2024 | Not set |
| 1.3 | Occupational standard, end-point assessment plan and funding band revised. | 15/03/2024 | 15/12/2024 |
| 1.2 | End-point assessment plan revised | 30/03/2023 | 14/03/2024 |
| 1.1 | End-point assessment plan revised | 11/02/2021 | 29/03/2023 |
| 1.0 | Retired | 23/11/2018 | 10/02/2021 |
Crown copyright © 2025. You may re-use this information (not including logos) free of charge in any format or medium, under the terms of the Open Government Licence. Visit www.nationalarchives.gov.uk/doc/open-government-licence